10kg/Set Anti-Abrasive Compound Wear Resistant Compound Used to Rebuild and Protect Chutes

Basic Info

Model NO.	Wearing Compound
Classification	Room Curing
Characteristic	Wear Resistance
Composition	Inorganic Material
Color	Grey/Yellow
Transport Package	500g/Set, 5kg/Set, 10kg/Set, 13.7kg/Set and 20kg/S
Specification	8kg/10kg
Trademark	Higlue
Origin	Jiangxi
HS Code	3506100090
Production Capacity	50000PCS/Day

Product Description

Features and BenefitsWearing Compound is a 2-part, grey, epoxy-based surface coating for metals. Ideal for protecting against coarse particle abrasion or erosion, or for rebuilding worn parts.Wearing Compound is a 2-part, grey, ceramic-filled, trowelable, epoxy-based surface coating designed to protect parts from coarse particle abrasion or erosion on metals (with or without chemical attack). It is designed for parts such as cyclones/separator bodies, dust collectors/exhausters, pump liners/impellers, fan blades and housings, chutes/hoppers and elbows/transition points.

• Protects metals from course particle abrasion
• Applied by trowel
• Suitable for chemical attack applications
• Renews worn surfaces fast

Ceramic Repair Putty* Renews worn surfaces fast and reduces* Downtime to put equipment back in service* Quickly Easy to mix and use* Non-sag paste allows application* Versatility for overhead& vertical surfaces* Non-shrinking* Extends wear life* Resists sliding abrasive wear* Eliminates costly wear part* Inventory Can be re-applied to* itself Contains ceramic beads 1-1.5mm Technical Infomation

Application method	Trowel
Applications	Protective Coating
Color	Gray
Cure type	Room Temperature (Ambient) Cure, Two Component Mix
Drying time	7.0 hr.
Key characteristics	Abrasion Resistant, Prolongs Equipment Life, Renews Worn Surfaces, Sag: Non-Sag, Wear Resistant
Mix ratio, by volume	2 : 1
Particle size	Large
Physical form	Paste
Substrates	Metal

Application

1. Cyclone and separator bodies
2. Dust collectors and exhausters
3. Pump liners and impellers
4. Fan blades and housings
5. Chutes and hoppers
6. Elbows and transition points

How to use

1. Cleaning:Remove dirt,oil, grease,loose flanky rust etc.,with a suitable high pressure water cleaning system .

2. Blasting:Blast all surfaces to be coated,with a sharp edged angular grit,such as aluminum oxide,to a depth of profile of approximately 75 microns and a degree of cleaniness of very thorough Blast Claeaning/Near Whitef.3. Cleaning:After blasting metal surfaces should be cleaned with a waterless or solvent,and allow the surface to dry before application of the product coat the surface before any oxidation or contamination takes place.4.Protection From Flash Rusting:To avoid flash rust,repairs should be made as soon as possible or within a mixmum 2 hours of blasting.5. Mixing The Material:Measure 2 parts resin to 1 part hardener by volume or weight if doing a partial kit.Otherwise,mixing a full kit is pre-measured at the correct ratio.For a full kit mix ,a spiral mixing blade attached to a high torque electric or pneumatic drill can be used.For a partial kit transfer measured quantities onto a clean and dry mixing surface to mix together witha trowel until uniform in color.If resin and hardener temperatures are 15ºC or below,preheat resin only,to about 30ºC but not to exceed 40ºC.6. Application:Apply fully mixed material to the prepared surface.Initially apply the material in a very thin layer to "wet" out the surface and ensure full epoxy contact with the roughened surface. Build up to desired thickness(minimum 6 mm),avoiding air entrapment.At 25ºC,the working time is 15 minutes and functional cure time is 4 hours Working and cure time depend on temperature and mass the higher the temperature and the larger the mass,the faster the cure.

Packaging & Shipping

500g/set, 5kg/set, 10kg/set, 13.7kg/set and 20kg/set10kg/set carton size: 32x32x32.5

FAQ

Q: Are you trading company or manufacturer ?
A: We are factory which over 20 years of experience,and provide you direct prices
Q: Can I be your agent?
A: Sure, we are looking for agent all over the world
Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: If I am not satisfied with the products ,when I get it,what should I do?
A: If not satisfied it, please feel free to contact salesman soon, we will provide you the solution ASAP.

Can also be customized according to your requirements, welcome to contact us!